Black+Decker Appliance Error Codes

Complete diagnostic guide for Black+Decker small household appliances including coffee makers, toaster ovens, dehumidifiers, dishwashers, and multi-cookers in the United States.

Important Note

Black+Decker appliances (part of Spectrum Brands) use various error codes that may vary by model and product type. Battery chargers use F-codes (F01-F07), while other appliances may use E-codes or other indicators.

Always refer to your specific model's user manual for model-specific error codes and troubleshooting procedures. When contacting Black+Decker support, have your model number and serial number ready.

Battery Charger Fault Codes

Error codes for Black+Decker battery chargers related to battery problems, charging issues, and power supply problems.

Error Code / Indicator	Meaning	Possible Causes	Solutions
F01	Internal short circuit in battery cell / Battery cannot charge	Internal short circuit in one battery cell Battery cell damaged Battery defective	Remove battery from charger Have battery checked by manufacturer Replace battery if defective Do not attempt to charge damaged battery
F02	Poor battery contact / Input voltage too low	Battery contacts dirty or corroded Battery not properly seated Input voltage below minimum requirement Power supply problem	Clean battery contacts Ensure battery is properly seated Check power supply and connections Try different power outlet Inspect charger contacts
F03	Open cell in battery / Battery cell problem	Open cell detected in battery Battery cell failure Battery needs inspection	Remove battery from charger Have battery inspected Battery may need replacement Contact Black+Decker support
F04	Charging time exceeded 18 hours / Battery may be damaged	Charging time exceeded 18-hour limit Battery may be damaged Battery not charging properly Charger malfunction	Remove battery from charger Check battery condition Try charging again Replace battery if damaged Contact support if problem persists
F05	Overheating / Charger too hot	Charger overheating Insufficient ventilation Ambient temperature too high Charger malfunction	Unplug charger immediately Allow charger to cool down Check ventilation around charger Move to cooler location Contact support if overheating continues
F06	Wrong polarity / Battery inserted incorrectly	Battery inserted with wrong polarity Battery contacts reversed	Remove battery Check battery orientation Reinsert battery with correct polarity Ensure proper alignment
F07	Generator / Mains voltage out of range	Mains voltage outside acceptable range Generator voltage problem Power supply issue	Check power supply voltage Try different power outlet Use proper voltage source Contact electrician if voltage problem

Dehumidifier Errors

Error codes for Black+Decker dehumidifiers related to sensors, water container, and system problems.

Error Code / Indicator	Meaning	Possible Causes	Solutions
LC	Child lock activated / Controls locked	Child lock feature enabled Safety lock activated	Hold Timer button for a few seconds to deactivate Check user manual for unlock procedure Child lock prevents accidental operation
ES / EH61	Evaporator coil temperature sensor error	Evaporator coil temperature sensor defective Sensor connection problem Sensor reading error	Turn off and unplug the appliance Wait 30 seconds and restart If error repeats, contact support Sensor may need replacement
AS / EH60	Room temperature sensor defective	Room temperature sensor defective Sensor connection problem Sensor reading error	Turn off and unplug the appliance Wait 30 seconds and restart If error repeats, contact support Sensor may need replacement
EH00	EEPROM error / Memory error	EEPROM memory error Control board memory problem System error	Try resetting the appliance Unplug and wait 30 seconds Plug back in and restart Contact customer service if problem persists
P2 / Eb	Water container full or not properly inserted	Water container is full Container not properly inserted Container sensor not detecting container	Empty water container Remove and reinsert container correctly Check container is properly seated Clean container and sensor area
E5	Pump installation error / Drain system problem	Pump not properly installed Drain system problem Pump malfunction	Check pump installation Inspect drain system Ensure proper pump setup Contact support if needed

Dishwasher Errors

Error codes for Black+Decker dishwashers related to heating, communication, and operational problems.

Error Code / Indicator	Meaning	Possible Causes	Solutions
E3	Heating error / Wash temperature not reached	Heating element not working Thermostat or sensor problem Wash temperature not reaching set point Heating circuit failure	Check heating element Inspect thermostat and sensors Allow cycle to complete Contact service for heating element replacement
Ed	Communication error between control boards	Communication error between PCBs Control board connection problem Wiring issue between boards	Check connection wires between boards Inspect control board connections May require service technician Contact Black+Decker support

Multi-Cooker and Washer-Dryer Errors

Error codes for Black+Decker multi-cookers and washer-dryer combo units.

Error Code / Indicator	Meaning	Possible Causes	Solutions
E1 (Multi-Cooker)	Temperature sensor error	Temperature sensor defective Sensor wiring problem Sensor connection issue	Check sensor, wiring, and connections Turn off and unplug appliance Restart after cooling Contact support if problem persists
E3 (Multi-Cooker)	Electronic disturbance / Circuit error	Electronic circuit problem Control board error System malfunction	Unplug appliance from power Wait 30 seconds and restart May require repair Contact service if error continues
E10 (Washer-Dryer)	Water inlet error	Water supply problem Inlet valve issue Water not entering machine	Check water supply Inspect inlet valve Ensure water tap is open Check inlet hose
E12 (Washer-Dryer)	Water overflow	Too much water in machine Overflow detected Water level sensor problem	Stop machine immediately Check for leaks Inspect water level sensor Contact service if problem persists
E21 (Washer-Dryer)	Drain problem / Drainage difficulty	Drain hose blocked or kinked Drain pump not working Drain filter blocked	Check drain hose for blockages Straighten kinked drain hose Clean drain filter Inspect drain pump
E30 (Washer-Dryer)	Door not properly closed	Door not correctly closed Door lock not engaged Door sensor not detecting closure	Open and close door properly Ensure door clicks into place Check door lock mechanism Inspect door sensor

Need More Help?

If you are experiencing problems with your Black+Decker appliance that are not covered by these error codes, or if the provided solutions do not resolve your issue, we recommend:

Consult your Black+Decker appliance user manual for model-specific information
Visit the official Black+Decker support page: blackanddecker.com/support
Contact Black+Decker customer service (Spectrum Brands) in the United States: 800-231-9786
Email support for home appliances: homeappliancesupport@spectrumbrands.com
Regular maintenance: clean appliances regularly, descale coffee makers, empty dehumidifier containers
Seek help from a qualified appliance repair technician
Check warranty coverage if your appliance is still under warranty

Go to Diagnostics Page Back to Brand Overview